Davide Ferraris

Mechanical and robotics engineer, Turin

I design the machines that build and test other machines: robot cells, grippers and test rigs for automotive and food suppliers in Piedmont. I take a project from the requirement to a signed-off machine on the factory floor.

Chartered engineer
Order of Engineers, Turin
Focus
Robot cells, end effectors, test rigs
Tools
SolidWorks, Ansys, MATLAB, ROS 2
Experience
14 years
Languages
Italian, English, German

Work

Welding cell with two robots and a car body fixture
1
Quick-change fixture, open
2
Simulation of robot reach envelopes
3
Cell layout before and after
4

Spot-welding cell retrofit

2025, Turin

Asked: Add a second car body variant to a 2009 welding cell without stopping the line for more than one weekend.

How: Laser-scanned the cell, rebuilt it in simulation and moved two robots 400 mm to reach the new weld points. A quick-change fixture swaps variants in under 90 seconds.

Result: Installed over one weekend. Cycle time 58 s, down from 64 s, and 212 weld points per body with no change to the floor plan.

Client: Tier 1 body supplier. Role: Lead mechanical engineer. Team: 3 engineers, 2 technicians.

Four-finger silicone gripper holding a peach
5
Finger moulds and cast parts
6
Gripper over a fruit tray
7

Gripper for soft fruit

2024, Cuneo

Asked: Pick peaches from a conveyor into trays at 40 picks a minute without bruising them.

How: Four silicone fingers on a vacuum-assisted palm, sized from 300 scanned fruits. Grip force is set by air pressure, closed-loop at 1 kHz.

Result: Bruise rate 0.4 % against 3 % for hand packing, at 42 picks a minute. Two lines running since July 2024.

Client: Fruit cooperative. Role: Design and testing. Partner: University lab, soft robotics.

Test rig with a gearbox clamped between two servo motors
8
Accelerometer mounting points
9

Gearbox end-of-line test rig

2023, Modena

Asked: Test every gearbox for noise and backlash before it ships, in under three minutes.

How: Two servo motors load the input and output shafts while accelerometers record the run-up. Pass and fail limits came from 600 gearboxes measured in the first month.

Result: 2 min 40 s per unit. Warranty returns for noise fell by two thirds in the first year.

Client: Driveline manufacturer. Role: Mechanical design, test method.

Cut-away of the hub motor showing the spiral coolant channel
10
Dynamometer test set-up
11

Hub motor cooling jacket

2022, Turin

Asked: Keep a wheel hub motor under 140 °C through a 20-minute hill climb.

How: Thermal model in Ansys, then three printed jacket designs tested on a dynamometer. The winner routes coolant through a spiral channel cast into the stator housing.

Result: Peak winding temperature 128 °C at full load. Adds 0.6 kg per wheel.

Client: Electric vehicle start-up. Role: Thermal and mechanical design.

Shoulder exoskeleton worn over a work jacket
12

Passive shoulder exoskeleton

2021, Milan

Asked: Reduce shoulder load for line workers who fit parts overhead all shift.

How: A spring and cam mechanism that supports the arm only above 70 degrees. Tested with 12 workers over four weeks.

Result: Shoulder muscle activity down 35 % in overhead tasks. Weighs 2.1 kg.

Partner: Politecnico research group. Role: Mechanism design.

About

I studied mechanical engineering at Politecnico di Torino and spent eight years at a robotics integrator, first on line design and then leading cell projects.

Since 2019 I work independently. I like problems with a hard number at the end: a cycle time, a temperature, a reject rate.

CV

Experience

  • 2019 to nowIndependent engineerRobot cells, end effectors and test rigs
  • 2011 to 2019Robotics integrator, TurinProject lead, automotive welding and assembly cells
  • 2010 to 2011Machine builder, IvreaDesign engineer, packaging machines

Education

  • 2010Politecnico di TorinoMSc Mechanical Engineering
  • 2009TU MunichExchange semester, robotics